Software: Apache/2.2.16 (Debian). PHP/5.3.3-7+squeeze19 

uname -a: Linux mail.tri-specialutilitydistrict.com 2.6.32-5-amd64 #1 SMP Tue May 13 16:34:35 UTC
2014 x86_64 

uid=33(www-data) gid=33(www-data) groups=33(www-data) 

Safe-mode: OFF (not secure)

/etc/   drwxr-xr-x
Free 129.88 GB of 142.11 GB (91.39%)
                            Encoder    Tools    Proc.    FTP brute    Sec.    SQL    PHP-code    Update    Feedback    Self remove    Logout    

Viewing file:     gai.conf (2.87 KB)      -rw-r--r--

# Configuration for getaddrinfo(3).
#
# So far only configuration for the destination address sorting is needed.
# RFC 3484 governs the sorting.  But the RFC also says that system
# administrators should be able to overwrite the defaults.  This can be
# achieved here.
#
# All lines have an initial identifier specifying the option followed by
# up to two values.  Information specified in this file replaces the
# default information.  Complete absence of data of one kind causes the
# appropriate default information to be used.  The supported commands include:
#
# reload  <yes|no>
#    If set to yes, each getaddrinfo(3) call will check whether this file
#    changed and if necessary reload.  This option should not really be
#    used.  There are possible runtime problems.  The default is no.
#
# label   <mask>   <value>
#    Add another rule to the RFC 3484 label table.  See section 2.1 in
#    RFC 3484.  The default is:
#
#label ::1/128       0
#label ::/0          1
#label 2002::/16     2
#label ::/96         3
#label ::ffff:0:0/96 4
#label fec0::/10     5
#label fc00::/7      6
#label 2001:0::/32   7
#
#    This default differs from the tables given in RFC 3484 by handling
#    (now obsolete) site-local IPv6 addresses and Unique Local Addresses.
#    The reason for this difference is that these addresses are never
#    NATed while IPv4 site-local addresses most probably are.  Given
#    the precedence of IPv6 over IPv4 (see below) on machines having only
#    site-local IPv4 and IPv6 addresses a lookup for a global address would
#    see the IPv6 be preferred.  The result is a long delay because the
#    site-local IPv6 addresses cannot be used while the IPv4 address is
#    (at least for the foreseeable future) NATed.  We also treat Teredo
#    tunnels special.
#
# precedence  <mask>   <value>
#    Add another rule to the RFC 3484 precedence table.  See section 2.1
#    and 10.3 in RFC 3484.  The default is:
#
#precedence  ::1/128       50
#precedence  ::/0          40
#precedence  2002::/16     30
#precedence ::/96          20
#precedence ::ffff:0:0/96  10
#
#    For sites which prefer IPv4 connections change the last line to
#
#precedence ::ffff:0:0/96  100

#
# scopev4  <mask>  <value>
#    Add another rule to the RFC 3484 scope table for IPv4 addresses.
#    By default the scope IDs described in section 3.2 in RFC 3484 are
#    used.  Changing these defaults should hardly ever be necessary.
#    The defaults are equivalent to:
#
#scopev4 ::ffff:169.254.0.0/112  2
#scopev4 ::ffff:127.0.0.0/104    2
#scopev4 ::ffff:0.0.0.0/96       14
#
#    For sites which use site-local IPv4 addresses behind NAT there is
#    the problem that even if IPv4 addresses are preferred they do not
#    have the same scope and are therefore not sorted first.  To change
#    this use only these rules:
#
#scopev4 ::ffff:169.254.0.0/112  2
#scopev4 ::ffff:127.0.0.0/104    2
#scopev4 ::ffff:0.0.0.0/96       14